home *** CD-ROM | disk | FTP | other *** search
/ Magnum One / Magnum One (Mid-American Digital) (Disc Manufacturing).iso / d22 / wd.arc / AR323 < prev    next >
Text File  |  1991-05-17  |  11KB  |  284 lines

  1.  
  2.      Western Digital is a registered trademark of Western Digital 
  3.      Corporation; IBM PC, AT and XT are registered trademarks of the 
  4.      International Business Machines Corporation; MS DOS, OS2 and PC DOS 
  5.      are registered trademarks of Microsoft Corporation.
  6.      
  7.                                    WD1003A-RA2
  8.                               Software Installation
  9.      
  10.      The format instructions that you follow are simple procedures to tell 
  11.      the computer that you have either one or two Winchester disk drives 
  12.      installed and prepares your operating system to recognize the Western 
  13.      Digital controller.  
  14.      
  15.      You will need to know the parameters of your hard disk drives.  As a 
  16.      convenience to you, we have included a list of the most common hard 
  17.      disk drives and their parameters.  To access this list, return to the 
  18.      STORAGE CONTROLLER menu.  If your drive is not listed, contact your 
  19.      drive manufacturer or consult your drive manual to determine drive 
  20.      type and parameters.
  21.                            TRANSLATION/NON-TRANSLATION
  22.      
  23.      The motherboard BIOS in most older IBM PC AT's or AT compatible 
  24.      systems do not recognize the 26 sector per track feature of RLL type 
  25.      drives.  If your hard disk drive has 4 heads and fewer than 663 
  26.      cylinders, you should select the translation mode controller card and 
  27.      install software using the instructions provided under the Software 
  28.      Instructions for Translation Mode.   If your drive has greater than 
  29.      663 cylinders, you will need to use the Software Instructions for Non-
  30.      Translation Mode.
  31.      
  32.                                       NOTE
  33.      
  34.      Translation is only available with F001 controllers. F000 controllers 
  35.      operate in non-translation mode only.  F001's translation program 
  36.      converts the drive's 26 physical sectors per track to 17 sectors per 
  37.      track.  The extra sectors are "translated" into logical heads.  To 
  38.      use the translation mode, select through the Setup program a 615 
  39.      cylinder and six head drive type.  (This is drive type three for IBM 
  40.      Personal Computer AT users.  Not all AT compatible systems use the 
  41.      same drive tables as IBM.)  This configuration must be used when 
  42.      running an operating system, application program, or system BIOS that 
  43.      requires a 17 sector per track disk drive.
  44.      
  45.      To format your hard disk drive, you may use one of several software 
  46.      programs.  The Advanced Diagnostics (or equivalent in AT 
  47.      compatibles), Disk Manager from Ontrack Computer Systems, or 
  48.      Speedstor 4.02 from Storage Dimensions.  Use of the programs depends 
  49.      on the controller configuration.  Configuring the controller to use 
  50.      the translation feature requires running the Advanced Diagnostics 
  51.      program, Setup.  Setup defines the drive type for the system and low 
  52.      level formats the drive.  Without translation, Advanced Diagnostics 
  53.      can low level format the drive, if the system BIOS recognizes the 26 
  54.  
  55.  
  56.  
  57.  
  58.  
  59.  
  60.  
  61.  
  62.  
  63.  
  64.  
  65.  
  66.  
  67.      sector RLL format.  (Storage Dimensions' Speedstor 286 BIOS is a 
  68.      replacement set of BIOS ROMs for the AT system board.)  Run the 
  69.      DOSprograms, FORMAT and FDISK, after performing the low level format, 
  70.      regardless of controller configuration.
  71.      
  72.      NON-TRANSLATION MODE - SOFTWARE INSTALLATION
  73.      
  74.      ...WARNING..................WARNING......................WARNING...
  75.      
  76.                     THE FOLLOWING LOW-LEVEL FORMAT PROCEDURE
  77.                     WILL DESTROY ALL DATA ON YOUR HARD DRIVE
  78.                       BACK-UP THE DATA ON YOUR DRIVE BEFORE
  79.                     CONTINUING WITH LOW LEVEL FORMAT ROUTINE
  80.      
  81.                                       NOTE
  82.      
  83.      Formatting hard disk drives with the non-translation operational mode 
  84.      requires a host system with a 26 sector BIOS.  If the system does not 
  85.      contain a 26 sector BIOS, Ontrack and Storage Dimensions produce 
  86.      programs to support the 26 sector RLL drives.  For further 
  87.      information on these programs, contact:
  88.      
  89.                 Ontrack Computer Systems
  90.                 6222 Bury Drive
  91.                 Eden Prairie, Minnesota 55344
  92.                 (612) 937-1107
  93.                 
  94.                 Storage Dimensions
  95.                 14127 Capri Drive, Suite 1
  96.                 Los Gatos, CA 95030
  97.                 (408) 370-3304
  98.                  
  99.      The Disk Manager and Speedstor products are the only products that 
  100.      have been tested by Western Digital at this publication date.  Both 
  101.      work well, providing full usage of the RLL capacities.  However, 
  102.      these are not the only alternatives for removing system limitations.  
  103.      Contact your dealer for further information.
  104.      
  105.                                      CAUTION
  106.                      Avoid system damage by consulting your
  107.                      Technical Reference manual to ensure that your
  108.                      drive type is supported by your host BIOS drive
  109.                      tables.  Not all AT-compatibles share the same
  110.                      drive tables as IBM.
  111.      
  112.      1.   Insert your system Advanced Diagnostic Diskette (or equivalent). 
  113.      
  114.      2.   Turn on power.
  115.      
  116.      3.   Boot diagnostic and select Setup option.  After defining drive 
  117.      types, run System Checkout.  Enter 0 after the "Select the action 
  118.      desired" prompt.
  119.      
  120.  
  121.  
  122.  
  123.  
  124.  
  125.  
  126.  
  127.  
  128.  
  129.  
  130.  
  131.  
  132.  
  133.      
  134.      4.   Select fixed disk option 17.
  135.      
  136.      5.   Select the Format Menu from the Fixed Disk Diagnostic Menu.
  137.      
  138.      6.   Unconditionally format the drive with the Format Selection Menu.
  139.      
  140.      7.   Enter bad block in the Defect Entry table.
  141.      
  142.      8.   Formatting begins.  After formatting the drive, press "Enter".  
  143.      Boot and operate the system normally.
  144.      
  145.      If you require further information or other technical support, please 
  146.      contact your authorized dealer.
  147.      
  148.      SOFTWARE INSTALLATION INSTRUCTIONS FOR TRANSLATION MODE
  149.      
  150.      ...WARNING..................WARNING......................WARNING...
  151.      
  152.                     THE FOLLOWING LOW-LEVEL FORMAT PROCEDURE
  153.                     WILL DESTROY ALL DATA ON YOUR HARD DRIVE
  154.                       BACK-UP THE DATA ON YOUR DRIVE BEFORE
  155.                     CONTINUING WITH LOW LEVEL FORMAT ROUTINE
  156.      
  157.                                      CAUTION
  158.                      Avoid system damage by consulting your
  159.                      Technical Reference manual to ensure that your
  160.                      drive type is supported by your host BIOS drive
  161.                      tables.  Not all AT-compatibles share the same
  162.                      drive tables as IBM.
  163.      
  164.      
  165.      1.   Insert your system diagnostic diskette (or equivalent in drive 
  166.      A.
  167.      
  168.      2.   Turn on the system power.
  169.      
  170.      3.   Boot diagnostic and select Setup option.
  171.      
  172.      4.   Set up the system for the proper configuration of diskette and 
  173.      fixed drives (drive type 3 for IBM), basze memory size, expansion 
  174.      memory size, and display.
  175.      
  176.      5.   After performing Setup, execute a low level format using the 
  177.      Advanced Diagnostics Diskette.  Follow the menu and reference manual 
  178.      instructions.
  179.      
  180.      6.   Load and execute the FDISK and FORMAT programs.  Follow the menu 
  181.      and reference manual instructions.
  182.      
  183.  
  184.  
  185.  
  186.  
  187.  
  188.  
  189.  
  190.  
  191.  
  192.  
  193.  
  194.  
  195.  
  196.  
  197.  
  198.  
  199.      
  200.                                  Troubleshooting
  201.      
  202.      Problem:   1790 Disk 0 Error.
  203.      
  204.      Cause:     No low level format on hard disk.  Wrong drive type
  205.                 selected. Not enough drive power.  Bad cables. Improper
  206.                 drive selection or termination.
  207.      
  208.      Problem:   Drive does not partition.
  209.      
  210.      Cause:     Check drive types.  Note that drive types for the AT
  211.                 and AT-compatibles differ.
  212.      
  213.      Problem:   "Error Reading Fixed Disk" appears when booting from
  214.                 hard drive.
  215.      
  216.      Cause:     DOS partition not active.
  217.      
  218.      Problem:   Winchester activity LED continuously lit.
  219.      
  220.      Cause:     No problem.  Drive LED selected for latched mode.
  221.      
  222.      Problem:   For systems with two drives, both Winchester activity
  223.                 LEDs light at the same time.
  224.      
  225.      Cause:     Improper drive selection or termination. Inspect the 
  226.                 drive cables. If the data cables are straight, then set
  227.                 drive C's drive select switches for drive select 1 and
  228.                 drive D's drive select switches for drive select 2. If
  229.                 the data cables have a twist, set both drives' select
  230.                 switches for drive select 2. Consult your drive manuals
  231.                 or dealer for drive switch settings. Finally, under no
  232.                 circumstances, use twisted floppy cables for the
  233.                 Winchester drive. Floppy and Winchyester drive interface
  234.                 connections differ significantly.
  235.      
  236.      Problem:   Slow and inefficient operation.
  237.      
  238.      Cause:     The biggest culprit for this problem is an incorrect 
  239.                 interleave factor.  Therefore, some experimentation with
  240.                 the interleave factor may be necessary. (Refer to the
  241.                 format instructions for setting interleave factor).
  242.                 Interleave factors are very dependent on the host
  243.                 operating system and application.
  244.      
  245.      Problem:   Not getting full capacity from drive.
  246.      
  247.      Cause:     You may have an MFM type drive.  Consult your drive 
  248.                 manual.  The WD1003A-RA2 is designed for use with RLL
  249.                 type drives only.  DO NOT USE WITH MFM DRIVES.
  250.      
  251.  
  252.  
  253.  
  254.  
  255.  
  256.  
  257.  
  258.  
  259.  
  260.  
  261.  
  262.  
  263.  
  264.  
  265.      Problem:  Controller does not format a Seagate ST225 to 30 megabyte.
  266.      
  267.      Cause:     The ST225 is a 20 megabyte MFM drive.  The ST238 is a 30 
  268.                 megabyte RLL drive.  This is a good time to point out the 
  269.                 differences between RLL and Modified Frequency Modulation 
  270.                 (MFM) disk drives and controllers.  First, RLL equipment 
  271.                 is able to record 50% more data on the drive.  Second, RLL 
  272.                 drives must be physically formatted with 26 sectors 
  273.                 because of the greater data density.  DO NOT UNDER ANY 
  274.                 CIRCUMSTANCES CONNECT A RLL CONTROLLER TO AN MFM DRIVE.
  275.      
  276.                 RLL controllers physically format any attached drive into 
  277.                 26 sectors.  Therefore, the RLL controller squishes 26 
  278.                 sectors onto a drive designed for 17 sectors.  Squishing 
  279.                 the RLL data onto a MFM drive results in corrupted data.  
  280.                 Finally, the chip sets on RLL and MFM controllers 
  281.                 significantly differ as a result of the first and second 
  282.                 points.
  283.      
  284.